Header Image - ALL POWER JACK

Category Archives

3 Articles

Lumberjack Tools

by adminpower

You could say you have two forms of lumberjacks. The ones who log trees for paper and lumber companies and the ones who work for tree services companies and do tree removal and tree pruning.

Historical Lumberjacking

A hundred years ago, no one except the very wealthy would have thought about pruning trees. It was hard laborious work because it was all done with hand tools. Not that it is that easy now, but in comparison it is easy now. Or maybe, it is just as hard work, but they get more done in the same time because of the power tools.

Some of the hand tools you needed were a long handles falling axe and a crosscut falling saw. These saws had a handle on each end and a lumberjack stood on either side of the tree and pushed and pulled the saw. They had huge teeth an inch or two long.

They also used a sledge hammer and wedges. Once the saw was in a ways, they would use the sledge hammer to drive the wedge into the cut behind the saw to keep the cut open, so the saw wouldn’t get pinched by the tree which would make it impossible to move the saw or remove it.

Modern Lumberjacks

Modern lumberjacks still have axes but they primarily use large chain saws. There are even machines that will come along and grasp the tree, snip it like it was cutting a flower stem, then tilt it over and pull it through the grippers to take all the branches off and in just a few minutes you have a log readied to be carried out of the forest. It is very impressive to see. Kind of scary too.

Tree Service Companies

With the tree services companies, the requirements are a bit different. With modern lumberjacks, they can pretty much fell a tree any direction they want. They will try to avoid knocking down other trees, but they generally don’t have to worry much about damaging anything. Not true for tree services companies. If they drop a tree on a house or prize flower garden, the clients are not going to be happy.

Rather than just felling the tree, they normally have to take them down piece meal. They will climb the tree, and rope off so that if they fall, the rope will catch them. They will attach other ropes to limbs they are cutting and lower them to the ground instead of letting them fall. This way they can use the ropes to guide where and how they are going to come down to the ground. So bit by bit, they deconstruct the tree until it is just a stump.

Once that is done, they will probably use a stump grinder to take the stump down below ground level so you can put dirt over it and it will look better. Lumberjacks will just leave the stumps there to rot. They have no reason to do stump grinding.

So the tree service companies will use chain saws but smaller ones than lumberjacks who are typically cutting down larger trees, although not necessarily. They also use the ropes and possible tackle up in the trees whereas a lumberjack might use them to move a tree once it is on the ground but that is about it.

Old Tools

by adminpower

As one of the contributors to this blog, I thought I would tell you about some of the tools I grew up with. What is really freaky is that now I sometimes go to museums and see tools that I grew up working with. Although, that probably isn’t too surprising because until the explosion of power tools, your basic tools hadn’t changed all that much over the last couple hundred years. Even now, a hammer is a hammer.

Granted, there are a lot of variations on the basic tools, back then and now as well. Plus, people have always made tools for specific purposes. In archeological sites from only 100 or 150 years ago,  they find tools they recognize but also tools that they have no idea what their purpose was.

To give an idea of how things have changed I will tell this story on myself. A few years back someone gave me an intelligence test for entrance into the army in World War I. I figured it would be easy because I am well educated. Well, I came out at the level of imbecile. The reason was that many of the questions had to do with horses or current events. Things that most people knew then but not now. I did an online search and found some tests but not the same one. Apparently there were a number of variations that were used. The ones I just found weren’t that difficult although some had current events from that time era. Click here for an example. If you search, you can find many more variations.

I remember enjoying using a bit and auger with my father when I was little. You never see these anymore. People just use power drills. Another one you don’t see much of anymore are planes. They had a blade sticking a bit out of the bottom and you could take layers of wood off. Much faster than sanding. Once again, people now just use power sanders or planes and other tools that are powered.

One of the most unusual was a type of plane. Unfortunately it was stolen so I no longer have it. It was my grandfather’s. It was used for planing an edge, say perhaps a picture frame. But it would plane two edges or sides at once. Rather than being flat, the plane’s bottom was shaped in a right angle. The blade also had a right angle in it. So when you planed something, you would get a perfect right angle and two sides would be planed at once. Wish I still had it.

Mills as Giant Tools

by adminpower

Have you ever been to a mill? There were saw mills and woolen mills and grain mills and more. They were basically huge tools or machines. Nowadays they have been shrunk and a combine going along the field basically does most of what a mill originally did.

At first, they were all water powered and then later many switched motors. Some later used turbines powered by the water flow instead of the water wheels. The water wheels always had a direct mechanical linkage. The turbines which were more efficient than the water wheels could be also set up with a direct mechanical linkage. Or they could be used to generate electricity to drive motors to drive the machinery.

If you have never been to a mill, you should. They were a marvel of 1700s and 1800s engineering. And you wouldn’t believe how many there were. On the US East Coast there were thousands of them. In Pennsylvania alone there were almost 2,000 of them. Possibly more.

Interestingly many were on fairly small streams and creeks leading into larger rivers. It took a bit to get the water wheel turning, but once started, it didn’t take much water to keep it going.

When a farmer would come to the mill with a wagon of grain to be milled, it would be typically be hoisted to the top floor. That is why with most mills you will see a large beam extending out from the peak of the roof with a pulley that was used to hoist the grain and any equipment and supplies they needed on upper floors.

They then made use of gravity and as the grain was processed it normally moved down through the mill. One of the first things that would be done was to put it in a separator. The amazing thing is that these have changed little in design over the last 150 years. In fact, one company said they still use the same size screens as they did in the 1850s. So if you have an antique separator, you can buy a screen from them and it will fit fine.

The separator has shafts that are rotated by whatever power source is currently used. The shafts spin a blower and also a shaker. The grain goes on top of a larger screen. The grain and smaller contaminants drop through and the chaff and larger particles are blown away. Typically they would be blown down a tube and out one end of the mill, usually over the river. A biologist said that that this practice significantly changed the ecology of the river around the mill.

Then the grain lands on a smaller screen that is too small for the grain to fall through but dirt and weed seeds fall through and are carried away, leaving just the grain.

Then the grain would be taken down to the mill wheels to be ground into flour. Then the flour would be bagged or boxed and moved down to be shipped out.

Over time different devices were invented to make the mill work less labor intensive. A major inventor in this regard was Oliver Evans. His mill, Greenbank Mill in Delaware still operating as a museum. Besides revolutionizing how mills worked, he also other important inventions, in particular the high pressure steam engine.

Going to one of these mills and seeing what they did with wood and iron is rather incredible. Today it looks clunky and antiquated but at one time it was cutting edge technology.